Empire Comfort Systems CP User Manual download pdf (Page 3)

26419-0-0809 Page 3

Countdown Timer

The Countdown Timer Mode allows the control to operate the

unit for up to 3 hours, in 10-minute increments. It can be operated

in either the Manual or Thermostat Modes.

1. To enter Timer Mode, press and release the TIMER button.

The Timer icon will ash.

2. Press the UP or DOWN button to set the running time, in

10-minute increments. Press and release the SET button.

The timer will run for the set time duration.

3. Pressing the TIMER button while in Timer Mode will ter-

minate the Timer operation. The Timer operation will also

terminate if the MODE button is cycled to off.

Thermostat Mode

The unit is placed in Thermostat Mode using the MODE button.

Placing the unit in Thermostat Mode will activate the numbers in

the smaller window on the LCD screen.

1. Press the UP or DOWN button to change the thermostat set

temperature. When the desired set temperature appears, press

and release the SET button to set.

2. If the SET button is not pressed, the set temperature will au-

tomatically be set after 5 seconds.

3. The Thermostat Mode can be de-activated by pressing the

MODE button.

Thermostatic Flame Modulation

This control can perform Main Flame Modulation using the Ther-

mostat. The control will shut the unit off when the room tem-

perature reaches 2° above set temperature. The Thermostat will

automatically modulate the main ame as follows:

2° above set temperature OFF

1° above set temperature Flame Level 1

at set temperature Flame Level 2

1° below set temperature Flame Level 3

2° below set temperature Flame Level 4

3° below set temperature Flame Level 5

4° below set temperature Flame Level 6

5° below set temperature Flame Level 7

Manual Flame Modulation – Main Flame

To change the Flame Level manually, press the FLAME MAIN

button. The current level will show in the MAIN box on the LCD

screen.

1. Press the UP or DOWN button to change the Flame Level.

2. When the unit is turned on, whether in Manual, Thermostatic,

or Program Mode, the Main Flame will automatically ignite

at the High (7) setting. After 5 seconds, the ame will default

to the previous setting.

Manual Flame Modulation – Rear Flame

Not available on all models

To change the Rear Flame Level, press the FLAME REAR

button. The current level will show in the REAR box on the LCD

screen.

1. Press the UP or DOWN button to change the Rear Flame

Level.

2. When the unit is turned on, whether in Manual, Thermostatic,

or Program Mode, the Rear Flame will automatically ignite at

the High (3) setting. After 5 seconds, the ame will default to

the previous setting.

Note: The rear ame level is dependant upon gas ow through

the main valve. Therefore, if the Main Flame setting is less than

high, the rear ame gas ow will be reduced proportionately at

all levels.

Fan Control

The unit must be ON to operate the Fan.

The Fan will turn on after 5 minutes of operation. Once the Fan

comes on, it can be controlled using the FAN button.

1. Press the FAN button, and the fan icon and speed will appear

on the LCD screen.

2. Press the UP or DOWN button to control the fan speed (0-6).

Press the DOWN button until 0 Level is reached to turn the

Fan off.

3. The fan will run for 12 minutes after the unit is shut off in any

mode. The fan may not be controlled during this period.

Accent Light

Not available on all models

The unit does NOT have to be on to operate the lights.

Lights are controlled by the LIGHTS button on the transmitter.

1. Press the LIGHTS button and the light icon and intensity

level will appear on the LCD screen.

2. Press the UP or DOWN button to set the light intensity level.

Press SET, or wait 7 seconds, and the light intensity setting

will be established.

Continuous Pilot

The unit can be changed from Intermittent Pilot Ignition (IPI), to

Continuous, or standing, pilot.

1. To place the unit in continuous pilot mode, press and release

the PROG/TIME and the FLAME MAIN buttons simultane-

ously. Continuous Pilot will appear on the LCD screen.

2. Repeat the simultaneous PROG/TIME and FLAME MAIN

push to place the unit back in IPI mode.

3. This feature can also be activated by the Continuous Pilot

(On/Off) switch on the Main Module.

1 2 3 4

Comments to this Manuals

No comments

Empire Comfort Systems CP User Manual Page 3

Comments to this Manuals

Related products and manuals for Fireplaces Empire Comfort Systems CP