Empire Comfort Systems OP42FP72M(N Owner's Manual download pdf (Page 7)

27777-8-0413 Page 7

Model OP36FP OP42FP

Input Maximum 40,000 50,000

Minimum 36,000 LP / 38,000 NAT 36,000 LP / 38,000 NAT

Orice P245 #50 LP / P209 #31 NAT P300 #48 LP / P280 #29 NAT

Accessories

BD36SS 36" Bifold Glass Door - Stainless Steel

BD42SS 42" Bifold Glass Door - Stainless Steel

DT36SS 36" Drain Tray - Stainless Steel

DT42SS 42" Drain Tray - Stainless Steel

WD36SS 36" Weather Door - Stainless Steel

WD42SS 42" Weather Door - Stainless Steel

SPECIFICATIONS

Check all local codes for requirements, especially for the size and

type of gas supply line required.

Recommended Gas Pipe Diameter

Pipe Length Schedule 40 Pipe

Inside Diameter

Tubing, Type L

Outside Diameter

Nat. L.P. Nat. L.P.

0-10 feet

0-3 meters

1/2”

12.7mm

3/8”

9.5mm

1/2”

12.7mm

3/8”

9.5mm

10-40 feet

4-12 meters

1/2”

12.7mm

1/2”

12.7mm

5/8”

15.9mm

1/2”

12.7mm

40-100 feet

13-30 meters

1/2”

12.7mm

1/2”

12.7mm

3/4”

19mm

1/2”

12.7mm

100-150 feet

31-46 meters

3/4”

19mm

1/2”

12.7mm

7/8”

22.2mm

3/4”

19mm

Note: Never use plastic pipe. Check to conrm whether your local

codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is

always best to consult your local authority and installation code.

Note: Be sure to install gas line cover to appliance prior to completing

gas line connection.

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

A manual main gas cock should be located in the vicinity of the unit.

Where none exists, or where its size or location is not adequate,

contact your local authorized installer for installation or relocation.

Compounds used on threaded joints of gas piping shall be resistant

to the action of liqueed petroleum gases. The gas lines must be

checked for leaks by the installer. This should be done with a soap

solution watching for bubbles on all exposed connections, and if

unexposed, a pressure test should be made.



be disconnected from piping at inlet of control valve and pipe

capped or plugged for pressure test. Never pressure test with

appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required by

the National Fuel Gas Code that a drip line be installed near the gas

inlet. This should consist of a vertical length of pipe tee connected

into the gas line that is capped on the bottom in which condensation

and foreign particles may collect.

The use of the following gas connectors is recommended:

— ANS Z21.24 Appliance Connectors of Corrugated Metal Tubing

and Fittings

— ANS Z21.45 Assembled Flexible Appliance Connectors of Other

Than All-Metal Construction

The above connectors may be used if acceptable by the authority

having jurisdiction The state of Massachusetts requires that a exible

appliance connector cannot exceed three feet in length.

Figure 1

GAS SUPPLY

1 2 3 4 5 6 7 8 9 10 11 12 ... 23 24

Comments to this Manuals

No comments

Empire Comfort Systems OP42FP72M(N Owner's Manual Page 7

Comments to this Manuals

Related products and manuals for Fireplaces Empire Comfort Systems OP42FP72M(N